Toyota Highlander 2004

[zaias]

Всем привет помогите как или чем прописать радиканал ЦЗ!!

бпелок прилагается в картинке 

skp-900 не смогла!

Изменено 20 декабря, 2017 пользователем zaias

[юрий65]

По старинке попробуй.

TOYOTA
Procedure
1. The vehicle should be in the following condition-A. The key is NOT inserted
in the ignition, B. The driver's door IS open, C. The driver’s door is
UNLOCKED.
2. Insert the Key into the ignition switch and then pull it out.
3. Press the Master Door Lock Switch 5 times from Lock to Unlock.
4. Close the Driver's door then open it.
5. Repeat step #3.
6. Now select the mode by inserting the key into the Ignition Switch and
turning it to the "Run" or "On" position. The programming mode is determined
by the amount of times you go from “key off” to the "key on" position
and back before pulling the key out.
A. 1 time is the "Add" mode. This is used only on some models and it allows
you to add a remote to the already existing remotes. The ECU confirms this by
locking and unlocking the door locks automatically after you remove the key.
B. 2 times is the second mode which will erase all previously programmed remotes
and allow you to program new ones. The ECU confirms this mode by
locking and unlocking the door locks twice after you remove the key
C. 3 times is the third mode which tells you how many remotes are already
programmed to the ECU. It confirms this locking and unlocking the door
locks the amount of times applicable to the remotes coded. If no remotes are
programmed then the ECU locks and unlocks the door locks 5 times. The ECU
will hold up to 4 remotes at any one time.
7. Press the Lock and Unlock buttons on the remote simultaneously for 1.5
sec and then press either button by itself for 1 sec.
8. The ECU will perform the Lock/Unlock automatically to confirm that the
1st remote is stored by the ECU. Repeat step 7 immediately with another
remote and continue until all remotes are registered.
9. Shut the driver’s door and try all remotes.

[zaias]

16 минут назад, юрий65 сказал:

По старинке попробуй.

TOYOTA
Procedure
1. The vehicle should be in the following condition-A. The key is NOT inserted
in the ignition, B. The driver's door IS open, C. The driver’s door is
UNLOCKED.
2. Insert the Key into the ignition switch and then pull it out.
3. Press the Master Door Lock Switch 5 times from Lock to Unlock.
4. Close the Driver's door then open it.
5. Repeat step #3.
6. Now select the mode by inserting the key into the Ignition Switch and
turning it to the "Run" or "On" position. The programming mode is determined
by the amount of times you go from “key off” to the "key on" position
and back before pulling the key out.
A. 1 time is the "Add" mode. This is used only on some models and it allows
you to add a remote to the already existing remotes. The ECU confirms this by
locking and unlocking the door locks automatically after you remove the key.
B. 2 times is the second mode which will erase all previously programmed remotes
and allow you to program new ones. The ECU confirms this mode by
locking and unlocking the door locks twice after you remove the key
C. 3 times is the third mode which tells you how many remotes are already
programmed to the ECU. It confirms this locking and unlocking the door
locks the amount of times applicable to the remotes coded. If no remotes are
programmed then the ECU locks and unlocks the door locks 5 times. The ECU
will hold up to 4 remotes at any one time.
7. Press the Lock and Unlock buttons on the remote simultaneously for 1.5
sec and then press either button by itself for 1 sec.
8. The ECU will perform the Lock/Unlock automatically to confirm that the
1st remote is stored by the ECU. Repeat step 7 immediately with another
remote and continue until all remotes are registered.
9. Shut the driver’s door and try all remotes.

Пробовал так он почему то не хочет заходить в режим программироывания не щелкает замком!! ((

[zaias]

Так и не прописался ключ!! Подскажите что можно купить для проверки. Ключей на их работоспособность 

[DIMAS0069]

Если для проверки радиоканала и накачки то использую AD35.

[sapr]

27 минут назад, DIMAS0069 сказал:

Если для проверки радиоканала и накачки то использую AD35.

 

...где можно почитать про его...И где брал? И впечатления какие...озвучь...

[DIMAS0069]

Где брал не помню давно это было)По работе,ложиш пультик посередине корпуса,жмеш все кнопы на нём-на экране показывает частоту пульта,накачку проверить -возле петли замка ставиш и если накачка есть бибикает,но не всегда удобно подносить-проще петля обходчика и диод на ней.Не бюджетно (где то около 8000тр было)но очень удобная вещица.

[END676]

http://www.carman-scan.ru/index.php?productID=295