Ford Transit 2.4 дизель - не заводится

[Ra2007]

Ford Transit 2.4 дизель - не заводится, поменяли насос на б\у, сканер выдает ошибку B2139. Я так понимаю что иммобилайзер не разрешает запуск с этим насосом. Подскажите пожалуйста что делать. Есть два сканер Ford IDS и Autoboss. Я еще не очень научился ими работать в ids ни как не найду где привязать насос к этому PCM.

[xak008]

какой насос? VR или VP

[xak008]

год машины, от чего поменяли насос? что явилось причиной? скорее всего проблема в ключе.

[Ra2007]

год машины, от чего поменяли насос? что явилось причиной? скорее всего проблема в ключе.

2002 г.в. поменяли из-за накрывшегося блока управления насоса

 

год машины, от чего поменяли насос? что явилось причиной? скорее всего проблема в ключе.

а как прописать ключ?

[Ra2007]

какой насос? VR или VP

vp30

[xak008]

Remote alarm/central locking

 

System operation

• Pressing remote control lock button once locks the vehicle and activates the alarm.
  
• Indicators will flash once.
  
• Pressing remote control lock button twice within 3 seconds activates double locking system and alarm.
  
• Indicators will flash twice.
  
• Transit Van:
  
  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks driver's and passenger's front door.
      
    • Pressing remote control unlock button twice within 3 seconds deactivates alarm and unlocks all doors.
      
    • Pressing tailgate release button once unlocks the tailgate/rear doors and sliding door.
      

  [*]Transit bus/kombi:

  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks all doors.
      

  [*]Transit Chassis cab/flatbed:

  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks driver's door.
      
    • Pressing remote control unlock button twice within 3 seconds deactivates the alarm and unlocks all doors.
      

Programming

 

When

• Remote control added or replaced.
  
• System malfunction.
  

How

• Obtain all remote controls.
  
• Switch ignition from OFF to ON 8 times within 10 seconds ensuring the ignition remains ON the 8th time.
  
• Programming mode activated (doors lock then unlock).
  
• Within 20 seconds:
  
  • 
    
    • Press and release any button on first remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on second remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on third remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on fourth remote control.
      
    • Doors lock then unlock to indicate correct programming.
      
    • Switch ignition OFF (doors lock then unlock). Programming mode deactivated.
      

NOTE: A maximum of 4 remote controls can be programmed, including original remote controls.

Battery replacement

 

Immobilizer

 

NOTE: On early models the system LED can be found next to the clock in centre fascia. On late models the system LED can be found in the instrument panel.

System operation

• System arms 5 seconds after switching ignition OFF.
  
• System LED will flash every 2 seconds when system armed.
  
• Switch ignition ON.
  
• Ensure system LED illuminates for approximately 3 seconds.
  
• If LED remains ON for 1 minute or flashes at regular intervals for 1 minute, then flashes at irregular intervals:
  
  • 
    
    • Key code not recognised.
      
    • Remove key and try again.
      

Programming

 

When

• System malfunction: System LED remains ON for 1 minute or flashes at regular intervals for 1 minute, then flashes at irregular intervals.
  
• Key added or replaced.
  

How

• Within 5 seconds:
  
• Obtain 2 programmed keys (A and B).
  
• Insert key A into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key A.
  
• Insert key B into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key B.
  
• Programming mode now activated.
  
• Within 10 seconds:
  
• Insert key to be programmed into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key.
  
• Repeat above procedure to program remaining keys.
  
• To exit programming mode switch ignition OFF, remove key, wait 5 seconds.
  
• Using new programmed key, switch ignition ON and start engine.
  
• If engine does not start and LED flashes:
  
• Switch ignition ON. Wait at least 20 seconds.
  
• Switch ignition OFF. Repeat programming procedure.
  
• Keys can also be programmed using diagnostic equipment.
  

NOTE: A maximum of 8 keys can be programmed.NOTE: If the system is in spare key programming 'disabled' mode, the above procedure will not work. Diagnostic equipment will be required to change to spare key programming 'enabled' mode.

 

батарейку проверь! и прокачай систему хорошо, что бы ни грамма воздуха не было

[Ra2007]

Remote alarm/central locking

 

System operation

• Pressing remote control lock button once locks the vehicle and activates the alarm.
  
• Indicators will flash once.
  
• Pressing remote control lock button twice within 3 seconds activates double locking system and alarm.
  
• Indicators will flash twice.
  
• Transit Van:
  
  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks driver's and passenger's front door.
      
    • Pressing remote control unlock button twice within 3 seconds deactivates alarm and unlocks all doors.
      
    • Pressing tailgate release button once unlocks the tailgate/rear doors and sliding door.
      

  [*]Transit bus/kombi:

  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks all doors.
      

  [*]Transit Chassis cab/flatbed:

  • 
    
    • Pressing remote control unlock button once deactivates alarm and unlocks driver's door.
      
    • Pressing remote control unlock button twice within 3 seconds deactivates the alarm and unlocks all doors.
      

Programming

 

When

• Remote control added or replaced.
  
• System malfunction.
  

How

• Obtain all remote controls.
  
• Switch ignition from OFF to ON 8 times within 10 seconds ensuring the ignition remains ON the 8th time.
  
• Programming mode activated (doors lock then unlock).
  
• Within 20 seconds:
  
  • 
    
    • Press and release any button on first remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on second remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on third remote control.
      
    • Doors lock then unlock to indicate correct programming.
      

  [*]Within 20 seconds:

  • 
    
    • Press and release any button on fourth remote control.
      
    • Doors lock then unlock to indicate correct programming.
      
    • Switch ignition OFF (doors lock then unlock). Programming mode deactivated.
      

NOTE: A maximum of 4 remote controls can be programmed, including original remote controls.

Battery replacement

 

Immobilizer

 

NOTE: On early models the system LED can be found next to the clock in centre fascia. On late models the system LED can be found in the instrument panel.

System operation

• System arms 5 seconds after switching ignition OFF.
  
• System LED will flash every 2 seconds when system armed.
  
• Switch ignition ON.
  
• Ensure system LED illuminates for approximately 3 seconds.
  
• If LED remains ON for 1 minute or flashes at regular intervals for 1 minute, then flashes at irregular intervals:
  
  • 
    
    • Key code not recognised.
      
    • Remove key and try again.
      

Programming

 

When

• System malfunction: System LED remains ON for 1 minute or flashes at regular intervals for 1 minute, then flashes at irregular intervals.
  
• Key added or replaced.
  

How

• Within 5 seconds:
  
• Obtain 2 programmed keys (A and B).
  
• Insert key A into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key A.
  
• Insert key B into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key B.
  
• Programming mode now activated.
  
• Within 10 seconds:
  
• Insert key to be programmed into ignition switch.
  
• Turn ignition switch to position II.
  
• Switch ignition OFF. Remove key.
  
• Repeat above procedure to program remaining keys.
  
• To exit programming mode switch ignition OFF, remove key, wait 5 seconds.
  
• Using new programmed key, switch ignition ON and start engine.
  
• If engine does not start and LED flashes:
  
• Switch ignition ON. Wait at least 20 seconds.
  
• Switch ignition OFF. Repeat programming procedure.
  
• Keys can also be programmed using diagnostic equipment.
  

NOTE: A maximum of 8 keys can be programmed.NOTE: If the system is in spare key programming 'disabled' mode, the above procedure will not work. Diagnostic equipment will be required to change to spare key programming 'enabled' mode.

 

батарейку проверь! и прокачай систему хорошо, что бы ни грамма воздуха не было

 

23 код ошибки выдает светодиод, и еще у меня только один ключ

Изменено 15 октября, 2012 пользователем Ra2007

[xak008]

когда крутишь стартером из насоса треск слышно?

[Ra2007]

когда крутишь стартером из насоса треск слышно?

слышно небольшое клацание

[xak008]

а сканер параметры какие нибудь кажет? автозапуск не стоит на машине?

[xak008]

теперь ко мне притащили транзит 2002 года с проблемой в насосе. умерла электроника. жду насос.

[xak008]

прошел почти месяц приволокли насос, отремонтировали старый. поставили прокачали, завели.

[Ra2007]

Тогда от меня утащили данный автомобиль в Москву. Вчера заезжал хозяин данной машины и рассказал что сделали у официалов.

А там просто поменяли солярку) И все завелось, даже сканер не подключали.....

[xak008]

в таких случаях для прокачки насоса надо повесить баченок с солярой, самотеком продавливает. после того как заведется шланги наместо